close
close

How To Remove Cast Iron Tub From Second Floor

Then, remove the drain from the bottom of the tub, saw the drain pipe off, and remove it too. Be safe and have a helper for these next few steps.


Plumbing fixed….new tub inserted, adding durarock to

Mark a line where the front edge of the tub rested on the floor or at least 2 inches beyond the.

How to remove cast iron tub from second floor. Your bathroom is on the second floor. Be sure to tape off the drain and fixtures, as well. But technology for bathtubs has come a long way.

Slide the tub out of the alcove using the 1 x 4 boards as skids. Older tubs made out of materials like cast iron or ceramics can weigh hundreds of pounds just on their own; Need to know if floor can take … read more

Remove any caulking around the perimeter of the tub and clean and dry thoroughly so your tape will stick. It sure is a great feeling to remove and replace a cast iron tub. How to remove a tub to install a shower.

Americast is part of that and it’s way lighter than cast iron. Cut away a horizontal strip of wall about 6 inches above the bathtub to reveal the tub flange, and remove any screws that secure the flange to the wall studs. You’ll want to tape around the base of the tub and up around the sides so you don’t get the product on the floor or shower surround.

First, turn off the water at the shutoff valve. On average, labor will cost around $2,000 but allows you to have confidence in the work and enjoy a new bathtub with less effort on your part. By this i mean is it eaiser to chop the tub up with a sledge hammer or try and lift the tub out of the bathroom ?

See also  How To Remove Shadows In Photoshop Cc

Even a small piece can weight 10 to 20 lbs. The tub will need to be removed before the floors can be worked on. Mount the tub closer to the wall).

Remove the old drain and trip lever. Clean the tub thoroughly with a scratchy pad and any product that has a bleaching agent. The edge of the coating will be hidden behind the refitted fixtures and a new bead of caulk.

The largest clawfoot tubs can weigh well over 500 pounds when dry and more than 1,000 pounds when filled with water. Open the can of refinisher and give it a gentle stir. In some cases, structural reinforcement of floors may be necessary if you want to install a large cast iron bathtub.

One person should lift the front edge of the tub, while another slides a couple of 1 x 4 boards underneath to get it off the floor. To prepare for refinishing, ayers first carves away the caulk between the tub and the walls and floor with a putty knife, then removes the drain cover and masks off the faucets. Filled weight is 738 lbs.

Those bad boys are heavy. Affordable materials include cast iron, acrylic, steel, and fiberglass bathtubs, which you can find for under $500. Apply your duct tape to the perimeter and tape down some heavy plastic to the floor.

Removing your cast iron tub might seem like a daunting task, but if you break it down into smaller steps, it should be relatively straightforward. Hi, i purchased a cast iron clawfoot tub that i would like to install on a second floor bathroom. Remove any stringer supports left on the wall.

See also  How To Charge A Deep Cycle Battery When Camping

Even a standard tub will likely require a couple of able bodies to move it. Sand the tub with a high grit, wet/dry sandpaper (600 grit or more). Another consideration for owners of old homes:

You can use a reciprocating. In addition, extra money in your budget may allow you to work with a contractor. I'm remodeling my second floor bathroom and would like to replace my castiron tub and tiled tub surround with a 4 piece acrylic tub and surround.

It is 355 lbs + 4 legs (do not know weight). If you have wood, vinyl or acrylic products to protect, apply a second layer of tape and two rows high around the tub. Mark a line on the floor 2 inches inside the wall, along the back and sides of the tub area.

The problem i have is i donot know how to remove the castiron tub once the piping is removed. “your bathroom floor must be strong enough to support not just the weight of the tub you choose, but the. Cut away all the old caulk from around the tub.

Amazing how sturdy those old tubs were back in the day…and still are. The terms refinishing, reglazing and resurfacing are often used interchangeably.


On Location East Meredith, N.Y. (Published 2015


Show me your pretty bath tile! Bathroom shower design


How 1 person can remove a 400 pound cast iron bathtub


Antique Claw Foot Tub Foot Used in Dennie's Resurfacing


Before and After Transforming our Bathroom from a 1940s


Mizzle painted cast iron bath Cast iron bath, Farrow and


Reglazing/Refinishing/Restoration Bathtubs, tiles, sinks


Pin on Bathroom ideas

See also  How To Reset Kenmore Washer Dryer Combo


Bath tube Girly bathroom, Bathtub, Bath tube


ANTIQUE AMERICAN STANDARD PORCELAIN & CAST IRON CORNER


24 Top Clawfoot Tub Bathroom Ideas & Designs for 2021


Pin by Grace Lesher on Fort Marshall Main Bathroom


Pin by Roxanne Osborne on Spa bath Free standing bath


KOHLER Bellwether 5 ft. LeftHand Drain CastIron Soaking


Pin on Cast iron sink


Vintage Tub & Bath on Instagram “This 1830s farmhouse


Cultured Marble… "Tub Surround" also great for all of


tub to shower conversion Google Search To Powder My


Bucket sink

Leave a Reply

Your email address will not be published. Required fields are marked *

Related Post